 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ANTENNA PRODUCTS DATA SHEET 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b Surface-mount ceramic multilayer antennas www.phycomp-components.com Product specification Supersedes data of 5th February 2001 2001 Sep 27 Rev.1 Phycomp Product specification Surface-mount ceramic multilayer antennas FEATURES * Designed for 2.45 GHz ISM-band * Simplifies antenna circuitry * NiSn lead-free terminations * suitable for wave and reflow soldering * Supplied in tape on reel. APPLICATIONS * Telecommunications * Computing (PCs, printers, PDAs) * Wireless office data communications including WLAN * Consumer electronics (wireless headphones). DESCRIPTION 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b ENVIRONMENTAL CARE The foil making process uses an environmentfriendly aqueous-solvent technology that fully complies with today's green-product design requirements. All terminations are lead-free. Packing materials can be recycled. This 2.45 GHz ceramic multilayer antenna has been designed to meet the requirements of the BluetoothTM(1) and IEEE 802.11b wireless communications protocol. It consists of a rectangular block of low-dielectric ceramic material and is fabricated in a water-based non-toxic process. The antenna is capable of providing good connectivity using near 50 microstrip directly onto the PC board. (1) Bluetooth is a trademark owned by Telefonieaktiebolaget L M Ericsson, Sweden. QUICK REFERENCE DATA DESCRIPTION Center frequency Bandwidth Gain VSWR Polarization Azimuth beamwidth Impedance Power dissipation Operating temperature Terminations Resistance to soldering heat Weight 100 MHz 1.2 dBi max. 2 max. Linear Omni-directional 50 1W -55 to +125 C NiSn 260 C for 10 s 0.16 g VALUE 2.45, 2.60 and 2.70 GHz 2001 Sep 27 Rev.1 2 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas MECHANICAL DATA 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b W S4 S3 S2 S2 S3 S4 C L C F G S1 T S1 F G Dimensions in mm For dimensions see Table 1. HBK016 Fig.1 Dimensional outline. Physical dimensions Table 1 L - Antenna dimensions W - T - F feed termination G optional1) ground termination C - S1 NC solder termination S2 NC solder termination S3 NC solder termination S4 NC solder termination Dimensions in millimetres 7.35 0.25 5.5 0.2 1.3 0.2 0.9 0.25 1.25 0.35 0.5 0.3 1.25 0.35 1.25 0.35 0.9 0.25 1.25 0.35 Note 1. The antenna has built-in circuitry to the ground termination. Connecting the antenna's ground point to the system's RF ground plane is optional. If good matching is achieved, the ground termination is then used as a solder joint (like S1, S2, S3, and S4) to fix the antenna to the substrate only. Device marking CENTER FREQUENCY (GHZ) 2.45 2.60 2.70 2001 Sep 27 Rev.1 MARKING CODE no marking 6 7 3 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas ELECTRICAL CHARACTERISTICS DESCRIPTION Center frequency Bandwidth Gain VSWR Polarization Azimuth beamwidth Impedance Power dissipation Operating temperature Terminations Resistance to soldering heat FOOTPRINT DIMENSIONS 100 MHz 1.2 dBi max. 2 max. Linear Omni-directional 50 1W -55 to +125 C NiSn 260 C, 10 sec. VALUE 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b 2.45, 2.60 and 2.70 GHz L C C S1 ANTENNA F S2 S3 W G S4 HBK015 Dimensions in mm For dimensions see Table 2. Fig.2 Recommended dimensions of solder lands. Physical dimensions Table 2 L - Recommended solder land pattern W - F feed pad G optional ground pad C - S1 NC mounting pad S2 NC mounting pad S3 NC mounting pad S4 NC mounting pad Dimensions in millimetres 8.30 0.10 5.70 0.10 1.00 0.10 1.40 0.10 0.90 0.10 1.40 0.10 1.40 0.10 1.00 0.10 1.40 0.10 2001 Sep 27 Rev.1 4 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b STANDARD TEST BOARD FOR RADIATION PATTERN AND SWR MEASUREMENTS 14 50 transmisson line 14 SMA connector antenna chip 8 0.8 1.2 Dimensions in mm HBK090 Fig.3 Typical FR4 test board. HBK089 50 25 3 GHz 2 GHz 10 +j 10 25 100 250 250 100 SWR 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 2.0 2.2 123 -j 10 0 21 3 250 25 100 HBK088 2.4 2.6 2.8 3.0 f (GHz) 50 Marker data: 1: SWR = 1.28; f = 2.400 GHz 2: SWR = 1.34; f = 2.450 GHz 3: SWR = 1.34; f = 2.500 GHz. Marker data: 1: 50.75 /12.36 ; f = 2.400 GHz 2: 44.98 /12.83 ; f = 2.450 GHz 3: 43.99 /12.27 ; f = 2.500 GHz. Fig.4 Typical SWR and characteristic impedance measurements. 2001 Sep 27 Rev.1 5 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b 0 0 -90 -40 -30 -20 -10 0 dBi 90 -90 -40 -30 -20 -10 0 dBi 90 180 HBK018 180 HBK019 E-plane H-plane (omni-directional) Fig.5 Typical radiation patterns. APPLICATION EXAMPLE 8 2 GROUND PLANE (on back side) CLEARANCE (no ground plane) Feedpoint ANTENNA CHIP 8 BLUETOOTH OR OTHER RF MODULE Ground CLEARANCE (no ground plane) 8 HBK014 Dimensions in mm 50 transmisson line (can be a straight connection) Note: The ground termination can be optionally connected to RF ground. Fig.6 Suggested layout. 2001 Sep 27 Rev.1 6 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas ORDERING INFORMATION 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b Components may be ordered by using either a simple 16-digit clear text code or Phycomp's unique 12NC. Ordering example for a 2.45 GHz antenna, 1000 pieces supplied in blister tape on 180 mm reel. Clear text ordering code EXAMPLE: AN2450000707051K PRODUCT AN AN = antenna CENTER FREQUENCY 2450 2450 = 2.45 GHz 2600 = 2.60 GHz 2700 = 2.70 GHz BANDWIDTH 00 00 = 100 MHz MATERIAL 07 07 = K7 SIZE 0705 0705 = 7.35 x 5.5 x 1.3 mm QUANTITY 1 1 = 1000 pcs 4 = 4000 pcs PACKING K K = 180 mm; 7" blister F = 330 mm; 13" blister B = bulk case 12NC ordering code EXAMPLE: 4311 111 00245 4 3XX 1 11 0 0XXX Family 43 antenna Center frequency 245 2.45 GHz 260 2.60 GHz 270 2.70 GHz Tolerance 00 100 MHz bandwidth (VSWR <2) Packing 11 180 mm / 7" reel, blister, 1000 pcs 12 330 mm / 13" reel, blister, 4000 pcs 13 bulk, 1000 pcs Material 1 high-frequency material Size 11 7.35 x 5.5 x 1.3 mm 2001 Sep 27 Rev.1 7 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas TESTS AND REQUIREMENTS Table 3 Test procedures and requirements IEC 60068-2 TEST METHOD 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b IEC 60 384-10 CECC 32 100 CLAUSE 4.4 TEST PROCEDURE REQUIREMENTS mounting The antenna may be mounted on a printed-circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive no visual damage 4.5 visual inspection any applicable method using x10 and dimension magnification check antenna adhesion frequency: 2.45 GHz @ 20 C a force of 5 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate mounted in accordance with CECC 32 100, paragraph 4.4 conditions: bending 1 mm at a rate of 1 mm/s; radius jig: 340 mm; 2 mm warp on FR4 board of 90 mm length 260 5 C for 10 0.5 s in a static solder bath 260 5 C for 30 1 s in a static solder bath no cracks or fissures larger than 4 mm standard test board from Fig.3 no visible damage 4.6.1 4.8 4.9 bond strength of plating on end face no visible damage no visible damage 4.10 20 (Tb) resistance to soldering heat resistance to leaching the terminations shall be well tinned after recovery; center frequency shift within 6% using visual enlargement of x10; dissolution of the terminations shall not exceed 10% 4.11 20 (Ta) solderability zero hour test and test after storage the terminations must be well (20 to 24 months) in original packing tinned for at least 75% in normal atmosphere; unmounted chips completely immersed for 2 0.5 s in a solder bath at 235 5 C -55 C (30 minutes) to +125 C (30 minutes); 100 cycles 500 12 hours at 60 C; 90 to 95% RH 500 12 hours at 125 C no visual damage; center frequency shift within 6% no visual damage; 2 hours recovery; center frequency shift within 6% no visual damage; 2 hours recovery; center frequency shift within 6% 4.12 4.14 4 (Na) 3 (Ca) rapid change of temperature damp heat 4.15 endurance 2001 Sep 27 Rev.1 8 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas PACKING Tape and reel specifications Tape and reel specifications are in accordance with "IEC 60286-3". Basic dimensions are given in Figs 7 and 8, and Tables 4 and 5. Peel-off force Peel-off force of the blister tape is in accordance with "IEC 60286-3" ; that is, at a peel-off speed of 300 10 mm/minute, 0.1 N to 1.3 N for 16 mm tape. The peel-off angle should be between 165 and 180. 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b Blister tape ENVIRONMENTAL CONSIDERATIONS * Cover tape, carrier tape and reel do not contain environmentally-harmful PVC materials. * Tape and reel are antistatic. * Because the carrier tape is made of polycarbonate, a homogeneous material (mono-plastic), it is ideally suited for recycling. * Compared to other PVC-free materials polycarbonate shows excellent stiffness and very little deformation with temperature. Blister tape specifications handbook, full pagewidth K0 T D0 P2 P0 E cover tape B0 F W MBG516 T1 T2 A0 P1 direction of unreeling D1 Cumulative pitch error: 0.2 mm over 10 pitches. Cumulative tolerance over 10 holes: 0.2 mm. K0: chosen so that the orientation of the component cannot change. For dimensions see Table 4. Fig.7 Blister tape. 2001 Sep 27 Rev.1 9 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas Table 4 Dimensions of blister tape; see Fig.7 SYMBOL A0 nominal clearance; note 1 B0 nominal clearance; note 1 K0 minimum clearance; note 1 W E F D0 D1 P0; note 2 P1 P2 T Notes 1. Possible product displacement in pocket. 2. P0 pitch tolerance over any 10 pitches is 0.2 mm. DIMENSION 5.85 7.60 1.70 16.0 1.75 7.50 1.55 1.50 4.0 8.0 2.0 0.30 TOL. 0.10 0.10 0.10 0.3 0.10 0.10 0.10 0.10 0.1 0.1 0.1 0.10 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b UNIT mm mm mm mm mm mm mm mm mm mm mm mm 2001 Sep 27 Rev.1 10 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas Reel specifications 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b W2 C N A HBK039 W1 Dimensions in mm. For reel dimensions see Table 5. Fig.8 Reel. Table 5 Reel dimensions; see Fig.8 QUANTITY PER REEL 1000 4000 TAPE WIDTH (mm) 16 A (mm) 180 0.1 330 0.1 C (mm) 13.0 0.5 13.5 0.1 N (mm) 62 0.5 100 0.1 W1 (mm) 16.0 +1/-0 16.5 0.1 W2 (mm) 20.5 0.2 21.1 0.1 2001 Sep 27 Rev.1 11 www.phycomp-components.com Phycomp Product specification Surface-mount ceramic multilayer antennas REVISION HISTORY Revision Rev.0 Rev.1 Date 2001 Feb 05 2001 Sep 27 Change Notification - - Description 2.45 GHz ISM-band antenna for Bluetooth and WLAN IEEE 802.11b - First issue of this specification - Specification status changed from "Preliminary" to "Product specification" - Product range expanded with 2.60 and 2.70 GHz devices - Revised antenna dimensions (see Table 1) - 180 mm tape-and-reel and bulk packing options added - Blister tape-and-reel specifications added - Clear-text code ordering information added 2001 Sep 27 Rev.1 12 www.phycomp-components.com |
Price & Availability of AN2450000707051B
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |